Lavatory Faucet

Model #77-1006

Large Photo

Specification: Double Handle Faucet With Brass Pop-Up

This Silver Series faucet offers superior value for the price.  From the quality chrome plated finish to the solid brass waterway it is built to last.  All Silver Series faucets come with a 5 year limited warranty against defects and leaks.  The washerless cartridge design assures you that it will last.  The crystal clear acrylic handles offer smooth operation even with wet hands.  The 2.0 GPM aerator conserves water while still allowing a smooth soft flow of water.  With the 1/2" IPS inlets the installation and hook-up is simple.  This faucet complies with NSF61-9 standards.  This faucet is available also without a 77-1005.

Specification: Pop-Up

This Silver Series Pop-up is a heavy duty brass unit with chrome finnish.  The smooth pivot action make opening the drain easy.  All washers and linkage is included for simple installation.  The same 5 year limited warranty applies so you know it will last.

Installation Instructions: Faucet

Step 1  Remove old faucet from sink and clean surface sink.

Step 2  Remove your Dominion Faucet from box and verify all parts for installation are available.

Step 3  Place the faucet from the top through the holes in the sink.

Step 4  Make sure that the faucet fits firmly and squarely on the surface of the sink. (If the faucet will not sit flat on the sink the use of plumbers putty or a chalking compound may be needed to to avoid water from leaking under the faucet.  Be sure to make sure plumbers putty will not stain the surface.)

Step 5  Screw the faucet mounting lock nut onto the 1/2 IPS connections until both sides are tight (do not over tighten).

Step 6  If using flexible connectors simply attach the 1/2" female pipe nut to the bottom of the 1/2" IPS connections.  (Make sure that the hot water side attaches to the left side of the faucet and the cold to the right.)

Step 7  Tighten the connector with wrench until tight (do not over tighten).

Step 6  If using flexible copper slide the nut over the copper tube then slide the cone washer over the tube with the flat side down.

Step 7  Attach the tube nut to the 1/2" IPS connections.  (Make sure that the hot water side attaches to the left side of the faucet and the cold to the right.)

Step 8  Use a wrench and tighten the nuts.

Step 9  Remove the aerator and turn the water on, after checking for leaks below allow water to fully flush the faucet and reinstall the aerator (check for leaks again).

Use the drawing below to help you with your installation:

Installation Instructions: Brass Pop-Up

Step 1  Remove the old pop-up from sink and clean surface of sink (make sure that the overflow is not clogged).

Step 2  Remove the pop-up collar and plunger from the pop-up body.

Step 3  Prepare the collar with plumbers putty or silicon caulk.

Step 4  With the lock nut and washer and gasket as far to the bottom as possible insert the pop-up from the bottom up.

Step 5  Screw the collar onto the pop-up body.

Step 6  From below use a wrench to tighten nut on the pop-up body until snug.

Step 7  Rotate the body so that the pivot opening faces straight back.

Step 8  With a wrench tighten the body nut until tight.

Step 9  Insert the plunger and then the pivot nut making sure that the pivot and the plunger engage.

Step 10 Slide the lift rod through the faucet from above.

Step 11 Slide the pop-up strap over the pivot and the strap using the spring clevis to hold them in place.

Step 12 Put plumbers putty or teflon tape on the tail piece and screw into the pop-up body.

Step 13 connect the P-trap.

step 14 Check for leaks.

Use the drawing below to help you with your installation:

Parts List:

Replacement cartridge XX-XXXX

Handles XX-XXXX

Aerator XX-XXXX

Connection Nuts XX-XXXX

Cone washers XX-XXXX

Handle Buttons XX-XXXX

Handle Screws XX-XXXX

Lock Nuts XX-XXXX

Plastic Pop-up XX-XXXX

Brass Pop-up XX-XXXX

Flexible Supply line 3/8" X 20" Stainless steel XX-XXXX